Alloy & tool steel
Hadfield manganese steel 1.3401 (X120Mn12)
Austenitic high-manganese steel that hardens under impact; for crusher jaws, liners and wear parts; plate and castings.
Manganese or Hadfield steel is an austenitic steel with about 12 % manganese and over 1 % carbon. Its wrought form is 1.3401, X120Mn12, and castings are made to ASTM A128 (for example grade A or B-2).
Its key property is work hardening: it is fairly soft and tough as delivered, and under impact and pressure its surface becomes very hard while the core stays tough. That makes it right for wear with impact, not for pure abrasion without impact.
A quote for your size and quantity
Send the grade, size, cut length and quantity on WhatsApp or with the form; our sales team reviews it and sends an offer.
Equivalents
- Material number (DIN)
- 1.3401
- EN name
- X120Mn12
- Standard
- SEW 395
- US equivalent, AISI/ASTM (approx.)
- ASTM A128 (castings)
- Iranian market name
- manganese steel, foolad mangenezi
- Nominal density
- 7.88 kg/dm³
Chemical composition
| Element | Range (%) |
|---|---|
| C | 1.10–1.30 |
| Si | 0.30–0.50 |
| Mn | 12.00–13.00 |
| P | ≤ 0.100 |
| S | ≤ 0.040 |
| Cr | ≤ 1.50 |
Mass %, ranges of SEW 395; the heat certificate of the delivered material is what the contract relies on.
Hardness and delivery state
Heated to about 1000–1050 °C and quenched in water (solution annealed) and supplied at about 200 HB; in service under impact the surface hardens to about 600 HV. As delivered it is non-magnetic.
Heat treatment
It is not hardened by ordinary quenching; its only heat treatment is solution annealing and a fast water quench. Reheating to roughly 300–800 °C embrittles it, so keep the heat input low when welding and use manganese steel electrodes. Work hardening makes it hard to machine.
Typical uses
- Crusher and mill jaws and liners
- Excavator bucket teeth and lips
- Rail crossings, switches and railway wear parts
- Wear plates and liners in mining and cement
Delivery forms and size ranges
- Plate
- On request
- Castings
- On request
The ranges the market offers, not a stock list. Rounds above about 100 mm are usually forged and traded in diameter bands.
Sizes and weights
Nominal weights at a density of 7.88 kg/dm³ (1.3401). The actual weight is weighed, and tool steel is usually sold by the weight of the cut piece.
| Thickness (mm) | kg per m² | 2000×6000 sheet (kg) |
|---|---|---|
| 10 | 78.8 | 945.6 |
| 12 | 94.56 | 1,134.7 |
| 15 | 118.2 | 1,418.4 |
| 20 | 157.6 | 1,891.2 |
| 25 | 197 | 2,364 |
| 30 | 236.4 | 2,836.8 |
| 40 | 315.2 | 3,782.4 |
| 50 | 394 | 4,728 |
What to include in your request
- Grade and material number, and the standard if your drawing requires one
- Form: round, flat or block, square or plate
- Exact size: diameter, width × thickness, or plate thickness
- Cut length, or the number and size of pieces, or full bars
- Delivery state: normalised, annealed, pre-hardened or quenched and tempered, turned
- Quantity in kg or tonnes, place and date of delivery
- Preferred origin (made in Iran or imported), if it matters to you
Documents you can ask for
- EN 10204 type 3.1 inspection certificate (heat analysis and hardness)
- Ultrasonic test (UT) report for forged sizes
- Hardness report for pre-hardened or quenched and tempered material
How is a quote for Hadfield steel 1.3401 worked out?
Unlike construction steel, alloy and tool steel has no single daily figure for every size, so none is published here. Each offer is worked out for the request, from these factors:
- Grade and standard: the alloying elements (chromium, molybdenum, vanadium, tungsten, nickel or cobalt) and any required standard or certificate
- Size and form: diameter or section, and round, flat, block, plate or forging; large forged sizes and rarely used sizes are checked one by one
- Cut length and number of pieces: a full bar differs from pieces cut to size, and cutting and weighing are part of the offer
- Delivery state: hot-rolled, annealed, normalised, pre-hardened or quenched and tempered, peeled or ground
- Quantity: a few kilograms for one part or tonnes for production
- Origin and documents: domestic or imported, and an EN 10204 type 3.1 certificate or ultrasonic test if you need one
- Delivery point and timing
For an exact offer, send your list with these details; our sales team reviews it and sends the offer.
Frequently asked questions
What is Hadfield steel 1.3401 steel?
Manganese or Hadfield steel is an austenitic steel with about 12 % manganese and over 1 % carbon. Its wrought form is 1.3401, X120Mn12, and castings are made to ASTM A128 (for example grade A or B-2).
What is the density of Hadfield steel 1.3401?
The nominal density of 1.3401 is about 7.88 kg/dm³ (g/cm³); the weight table on this page and the weight calculator use this value. The actual weight is weighed.
What is the equivalent of manganese steel 1.3401?
1.3401 is listed as X120Mn12 in the material sheet SEW 395 (Stahl-Eisen-Werkstoffblatt). The American specification for castings is ASTM A128, with grades A, B and C; there is no separate AISI grade. State the grade and standard you need in the request.
Why does manganese steel get harder in use?
It is austenitic: impact and pressure deform the surface layer and make it very hard, while the core stays soft and tough. Without impact this does not happen, and wear-resistant plates suit pure abrasion better.
What does a quote for Hadfield steel 1.3401 depend on?
On the grade and standard, the size and form, the cut length or number of pieces, the delivery state, the quantity, the origin and documents, and the delivery point and timing. That is why this group is quoted per request and not listed on the site.
How do I get a quote for Hadfield steel 1.3401?
Send the grade, form and size, the cut length or number of pieces, the delivery state and the documents you need. We review the request and send you an offer.