Alloy & tool steel

ASTM A105 forging steel for flanges and fittings

Carbon steel for forged piping components (flanges, fittings, valves) to ASTM A105; forgings and round bar.

ASTM A105 (and metric A105M) covers forged carbon steel piping components for ambient and higher-temperature service: flanges, fittings, valve bodies and similar parts, up to about 4540 kg per piece. Heavier forgings are made to ASTM A266.

A105 has no DIN material number; its closest European grade is P250GH (1.0460) to EN 10222-2, but it is not an exact equivalent. Its properties: tensile strength at least 485 MPa, yield strength at least 250 MPa and hardness at most 197 HB.

Looking for 'A106 plate'? A106 is seamless pipe, not plate; its specs and request form are on the seamless pipe page: Seamless pipe ASTM A106 Grade B

A quote for your size and quantity

Send the grade, size, cut length and quantity on WhatsApp or with the form; our sales team reviews it and sends an offer.

Equivalents

ASTM designation
A105
Closest EN grade
P250GH (1.0460)
Standard
ASTM A105/A105M
US equivalent, AISI/ASTM (approx.)
ASTM A105
Iranian market name
A105, A105 flange, A105 forging
Nominal density
7.85 kg/dm³

Chemical composition

ElementRange (%)
C≤ 0.35
Mn0.60–1.05
Si0.10–0.35
P≤ 0.035
S≤ 0.040
Cu≤ 0.40
Ni≤ 0.40
Cr≤ 0.30
Mo≤ 0.12
V≤ 0.08

Mass %, ranges of ASTM A105/A105M; the heat certificate of the delivered material is what the contract relies on.

Hardness and delivery state

Supplied as forged and, where needed, annealed, normalised, normalised and tempered, or quenched and tempered. The mill certificate (MTC) should show the heat analysis, tensile properties and hardness.

Heat treatment

Under ASTM A105, heat treatment is required for flanges above Class 300, special-design flanges under the stated conditions, and other components over NPS 4 that are above Class 300; the permitted treatments are annealing, normalising, normalising and tempering, or quenching and tempering. State the pressure class and any heat-treatment requirement in the request.

Typical uses

  • Flanges for oil, gas and steam piping
  • High-pressure forged fittings (tees, elbows, couplings)
  • Industrial valve bodies and parts
  • Forged parts of vessels and pressure equipment

Delivery forms and size ranges

Forgings (flanges, fittings, blocks)
On request
Round bar
On request

The ranges the market offers, not a stock list. Rounds above about 100 mm are usually forged and traded in diameter bands.

Sizes and weights

Nominal weights at a density of 7.85 kg/dm³ (A105). The actual weight is weighed, and tool steel is usually sold by the weight of the cut piece.

Round bar
Diameter (mm)kg per metre
Ø 5015.41
Ø 8039.46
Ø 10061.65
Ø 150138.72
Ø 200246.62
Ø 250385.34
Ø 300554.88

What to include in your request

  • Grade and material number, and the standard if your drawing requires one
  • Form: round, flat or block, square or plate
  • Exact size: diameter, width × thickness, or plate thickness
  • Cut length, or the number and size of pieces, or full bars
  • Delivery state: normalised, annealed, pre-hardened or quenched and tempered, turned
  • Quantity in kg or tonnes, place and date of delivery
  • Preferred origin (made in Iran or imported), if it matters to you

Documents you can ask for

  • EN 10204 type 3.1 inspection certificate (heat analysis and hardness)
  • Ultrasonic test (UT) report for forged sizes
  • Hardness report for pre-hardened or quenched and tempered material

How is a quote for ASTM A105 worked out?

Unlike construction steel, alloy and tool steel has no single daily figure for every size, so none is published here. Each offer is worked out for the request, from these factors:

  • Grade and standard: the alloying elements (chromium, molybdenum, vanadium, tungsten, nickel or cobalt) and any required standard or certificate
  • Size and form: diameter or section, and round, flat, block, plate or forging; large forged sizes and rarely used sizes are checked one by one
  • Cut length and number of pieces: a full bar differs from pieces cut to size, and cutting and weighing are part of the offer
  • Delivery state: hot-rolled, annealed, normalised, pre-hardened or quenched and tempered, peeled or ground
  • Quantity: a few kilograms for one part or tonnes for production
  • Origin and documents: domestic or imported, and an EN 10204 type 3.1 certificate or ultrasonic test if you need one
  • Delivery point and timing

For an exact offer, send your list with these details; our sales team reviews it and sends the offer.

Frequently asked questions

What is ASTM A105 steel?

ASTM A105 (and metric A105M) covers forged carbon steel piping components for ambient and higher-temperature service: flanges, fittings, valve bodies and similar parts, up to about 4540 kg per piece. Heavier forgings are made to ASTM A266.

What is the density of ASTM A105?

The nominal density of A105 is about 7.85 kg/dm³ (g/cm³); the weight table on this page and the weight calculator use this value. The actual weight is weighed.

What is the equivalent of A105?

A105 is an ASTM specification and has no DIN material number. Its closest European grade is P250GH (1.0460) to EN 10222-2, but the chemistry and tests are not the same. If your project calls for A105, ask for a certificate to that specification.

Is there 'A106 plate'? How do A105 and A106 differ?

ASTM A106 is the specification for seamless carbon steel pipe for high-temperature service (grades A, B and C), not plate. A105 is the steel for forged parts such as flanges and fittings, often used with A106 pipe. Carbon steel pressure plate is made to other specifications, such as A516.

What does a quote for ASTM A105 depend on?

On the grade and standard, the size and form, the cut length or number of pieces, the delivery state, the quantity, the origin and documents, and the delivery point and timing. That is why this group is quoted per request and not listed on the site.

How do I get a quote for ASTM A105?

Send the grade, form and size, the cut length or number of pieces, the delivery state and the documents you need. We review the request and send you an offer.