Buying guide
Buying Black Steel Sheet: Thickness, Size and Grade
To buy black steel sheet, take thickness and grade from the drawing and size it from the cutting plan. Weights for 2-6 mm sheet and 8-60 mm plate.
- Published:
- Updated:
- Reading time
- 4 min read

Contents
When buying black steel sheet, take thickness and grade from the drawing first, then choose the sheet size from your cutting plan. The Ahan Assa catalog lists hot-rolled sheet from 2 to 6 mm (EN 10051) and plate from 8 to 60 mm (EN 10029) in S235JR and S355JR; one square metre weighs about thickness × 7.85 kg.
What is the difference between black sheet and plate?
Black sheet is uncoated hot-rolled steel sheet, unlike coated sheet such as galvanized. Heavier gauges are sold as plate. In our catalog:
- S235JR hot-rolled sheet and its S355JR counterpart: 2 to 6 mm, tolerances to EN 10051;
- S235JR plate and S355JR plate: 8 to 60 mm, tolerances to EN 10029.
A 7 mm thickness is not listed. If a drawing calls for one, raise it with the engineer and the supplier before ordering rather than substituting another thickness yourself.
How do I choose the sheet thickness?
For structural work the buyer does not choose the thickness: the drawing and the structural engineer do. The buyer's job is to group the parts list by thickness and grade so the area needed for each is clear. Any change, up or down, needs the designer's approval. For base plates and connection plates, see our guide to steel plates in connections.
Which sheet sizes are in the catalog?
The catalog lists thin sheet in three sizes. The weights below are catalog nominal weights per sheet in kilograms, rounded to one decimal place.
| Thickness (mm) | Weight per m² (kg) | 1000×2000 sheet | 1250×2500 sheet | 1500×6000 sheet |
|---|---|---|---|---|
| 2 | 15.7 | 31.4 | 49.1 | 141.3 |
| 3 | 23.55 | 47.1 | 73.6 | 212.0 |
| 4 | 31.4 | 62.8 | 98.1 | 282.6 |
| 5 | 39.25 | 78.5 | 122.7 | 353.3 |
| 6 | 47.1 | 94.2 | 147.2 | 423.9 |
The plate sizes in the next table are all 6 m long; a 12 m size follows it. Weights are rounded to the nearest kilogram:
| Thickness (mm) | Weight per m² (kg) | 1250×6000 (S235JR only) | 1500×6000 | 2000×6000 |
|---|---|---|---|---|
| 8 | 62.8 | 471 | 565 | 754 |
| 10 | 78.5 | 589 | 707 | 942 |
| 12 | 94.2 | 707 | 848 | 1,130 |
| 15 | 117.75 | 883 | 1,060 | 1,413 |
| 20 | 157 | 1,178 | 1,413 | 1,884 |
| 25 | 196.25 | 1,472 | 1,766 | 2,355 |
| 30 | 235.5 | 1,766 | 2,120 | 2,826 |
| 40 | 314 | 2,355 | 2,826 | 3,768 |
| 50 | 392.5 | — | 3,533 | 4,710 |
| 60 | 471 | — | 4,239 | 5,652 |
A 2000×12000 size is also listed: for S235JR plate from 12 to 40 mm, and for S355JR plate at 12, 25 and 40 mm only. The full list, including 35 mm, is in the sheet and plate category.
Sheet size and cutting waste
The best sheet is the one that yields your parts with the least waste, not necessarily the largest or smallest. For example, for 500×500 mm parts a 1000×2000 sheet gives eight parts with no waste, ignoring the cut width. A 1250×2500 sheet gives ten parts but leaves a 250 mm strip, or 20% of the sheet area. Also check that the sheet can be unloaded and handled on site: a 20×2000×6000 sheet weighs about 1,884 kg.
Choosing a grade: S235JR or S355JR
The number in the grade name refers to the minimum yield strength at thin gauges, and the market names are ST37 and ST52. Nominal weight is the same in both grades, so weight cannot tell them apart: read the grade from the drawing, the quotation and the mill certificate. Our S235JR vs S355JR comparison covers strength, weldability and uses.
Estimating order weight
Steel density is about 7,850 kg/m³, which gives a simple formula:
Weight (kg) = thickness (mm) × width (m) × length (m) × 7.85
For a 10×1500×6000 sheet: 10 × 1.5 × 6 × 7.85 = 706.5 kg, matching the catalog's nominal weight. You can order by the kilogram, tonne or sheet, but sale is by actual weight, so leave room in your budget for the gap between nominal and weighbridge weight.
Quotation request checklist
- thickness, width and length in millimetres;
- the exact grade, not just the market name;
- number of sheets or total weight, and the order unit;
- whether a mill certificate is required;
- delivery location and unloading arrangements;
- a parts list and cutting plan if cutting is needed.
You can send your purchase list through our contact page for review.
Summary
The drawing sets the thickness and grade of black steel sheet; the buyer's part is to pick the sheet size that gives the least waste. Estimate weight with the formula above, and base the final amount on actual weight.
Frequently asked questions
What is the difference between black steel sheet and plate?
Plate is simply thicker black sheet. The Ahan Assa catalog lists hot-rolled sheet from 2 to 6 mm with EN 10051 tolerances and plate from 8 to 60 mm with EN 10029 tolerances.
How do I calculate the weight of a steel sheet?
Multiply thickness in mm by width and length in metres and by 7.85. A 10×1500×6000 sheet weighs 706.5 kg. That is a nominal weight; sale is by actual weight.
How is black steel sheet sold?
Sheet and plate in the Ahan Assa catalog can be ordered by the kilogram, tonne or sheet, but the final amount is based on actual weight.
What do ST37 and ST52 mean on steel sheet?
They are the market names for the grades S235JR and S355JR. The structural designer sets the grade, and the exact grade should appear on the quotation. Do not substitute one without the designer's approval.
Sources
- Ahan Assa public product catalog: grade, standard, thickness, dimensions and nominal weight of sheet and plate — Ahan Assa
By Ahan Assa Editorial Team
Related articles

Buying guide
SHS and RHS Hollow Sections: Sizes, Weights, Ordering
SHS and RHS hollow section sizes, wall thicknesses and weight per metre and per 6 m length, grade S235JRH to EN 10219-2, and what to specify on an order.
4 min read

Buying guide
IPE vs IPN Beam: Differences, Weight and Which to Use
IPE vs IPN beams: parallel or 14% tapered flanges, weight per metre and per 12 m, stiffness about both axes, taper washers and which beam to choose.
4 min read

Buying guide
How to Buy Rebar for a Building: Drawings to Delivery
How to buy rebar for a building: take the grade and bar sizes from the drawings, turn the bar schedule into tonnes, check the quotation and the delivery.
4 min read